Anchor Parameter Setting
Since there is no difference between Anchor parameter settings via UWB Dongle or via network equipment, the following only describes the device settings
A. Double click Anchor in the list
B. Click “Read” to display current setting and “Set” to apply and store the value
Anchor Parameter Description *Status of the operation will be display at the top of the window
-Device Id: ID of the device
-Type: Type of the equipment
-Reset: Anchor reboot, pleas click this button to acknowledge and apply the setting
-Range: Distance information between the dongle and anchor
Anchor Set
-Report ID Time: Report interval to indicate if an anchor is functional. Unit is in Seconds and the applicable range is 1 ~ 65535.
Server Set
-Server IP: IP address of server
-Server Port: Server Port Number
-Net Mode: Network selection
-Adaptive: Auto network configuration
-Lan: Connection type prioritization. Lan indicates wired, Wi-Fi indicates wireless.
Anchor Lan Set(Wired network configuration)
-IP Mode: IP settings, Static or DHCP.
-Lan Local Mac: Mac address.
-Local IP: Device static IP.
-Subnet Mask: Subnet Mask for static IP.
-GateWay: Gateway for the static IP
Anchor Wi-Fi Set(Wireless network configuration)
-IP Mode: Wi-Fi IP settings, Static or DHCP.
-Wifi Local Mac: Mac address for Wi-Fi connection, when anchor is not booted the value is 0,
unless the boot up is successful and detected or the value will remain as 0.
-Local IP:Device static IP.
-Wifi SSID:Wireless network name, maximum 32 characters.
-Wifi Password:Wireless network password, maximum 32 characters.
Note:
The anchor will prioritize wired connection when it detects the network is sourced from a wired interface, otherwise it will source the network from the Wi-Fi. On top of that, the Server IP has to be the IP address of the device executing the application, so as the communication protocol.
Attention: Whenever the anchor is started, it will begin the ping to server IP. Please make sure that the service device has the ICMP enabled. If the pinging fails, the anchor will reboot and configure the IP to 192.192.192.192 and the same event will keep on repeating unless the service responded. Then the anchor will return back to the functional state again.
C. Click Extended Function to access the advanced setting menu
Anchor Set
-ID: Anchor ID setting, 6 Byte, it is recommended not to modify this value
-Floor Num: Floor num of Anchor, used during area search function, default as 0
-Room Num: Floor num of Anchor, used during area search function, default as 0
Anchor Wifi Set
Wifi AP Mac: MAC address of Wi-Fi module, it is recommended not to modify this value
Debug(Debug Mode)
AT Command Testing
AT Command: AT command input
WaitTime: Waiting time for AT command reply
AT Command Reply: Reply of AT command
Wifi AP SSID: After filling in the Wifi SSID, one can read the condition of this Anchor connecting to this WIFI AP,for example (3,"DMATEKP2",-51,"ac:92:32:7f:f3:54",11,1,0)
Lan Last Connect Status:Latest connection status of LAN
List of returning status and definition:
-Lan_Connect_Start: Begin LAN connection.
-Lan_Conncet_OK: LAN is successfully connected.
-Lan_NetIc_Init_Failed: Network initialization failed.
-Lan_Phy_Connect_Failed: The physical layer connection failed; the cable is unconnected.
-Lan_Dhcp_Failed: DHCP failure.
-Lan_Ip_Conflic: IP address conflict.
-Lan_Get_Server_Gateway_Mac_Failed: MAC address of the server/gateway failed to obtain
-Lan_Ping_Server_Failed: pinging server has failed
Wifi Last Connect Status: Latest connection status of Wi-Fi
List of returning status and definition:
-Wifi_Connect_Start: Begin Wi-Fi connection.
-Wifi_Connect_OK: Wi-Fi is successfully connected.
-Wifi_No_SSID: Wi-Fi Network initialization failed.
-Wifi_AT_Failed:Wi-Fi AT command failed.
-Wifi_AT_CWMODE_CUR_Failed: Wi-Fi AT command failed.
-Wifi_ATE0_Failed: Wi-Fi AT command failed.
-Wifi_AT_CWDHCP_CUR_Failed: Wi-Fi AT command failed.
-Wifi_AT_CIPSTA_CUR_Failed: Wi-Fi AT command failed.
-Wifi_AT_CWJAP_CUR_Failed_TimeOut: Wi-Fi connection timed out.
-Wifi_AT_CWJAP_CUR_Failed_PasswordError: Wi-Fi password incorrect.
-Wifi_AT_CWJAP_CUR_Failed_NoAP: Non-existent AP.
-Wifi_AT_CWJAP_CUR_Failed_Else: Other error.
-Wifi_AT_CWJAP_CUR_Failed_NoReply: Wi-Fi no response.
-Wifi_AT_CIPSTART_Failed: WIFI AT command failed.
-Wifi_AT_CIPSEND_Failed: WIFI AT command failed.
-Wifi_Ping_Server_Failed: Server ping failed.
D. Factory Reset:To restore Anchor parameters back to default setting.
E. Height Offset Set: Only available on height sensor equipped models
Status: Status of height sensor module, Error indicates that height sensor does not exist
Anchor Height: Read the relative sea level of Anchor
Anchor Temp: Temperature of Anchor
Height Offset: Applicable offset range for the anchor, range is -32768 ~ 32767
Factory Reset: Restore Anchor height back to default setting